How to propagate Deutzia parviflora by cuttings

How to propagate Deutzia parviflora by cuttings

1. Seedling preparation:

First, make a good seedling bed. The length depends on the specific situation. The reference values ​​of width and height are one meter and fifty centimeters. Drainage holes need to be set at intervals of 0.5 meters. Then lay a layer of bricks on the bottom to facilitate drainage; lay the substrate on top and choose coarse river sand. Finally, the substrate should be sprayed and disinfected with a gray manganese oxide solution at a concentration of 2/1000. After half an hour, rinse the substrate with clean water until clean water flows out of the drainage hole.

2. Cutting selection and processing:

In early July, select one-year-old semi-lignified branches with short bud spacing for cuttings. Brown-green color is preferred and they have good flexibility. Measures should be taken to avoid water loss during transportation. Cut the branches to twelve centimeters to make cuttings, with a flat incision on the top and a horse ear shape on the bottom. Usually twenty of them are bundled together and then immersed in a rooting agent solution with a concentration of 500 mg per liter. They need to be soaked for twelve hours in preparation for cuttings.

3. Cutting:

When taking cuttings, the reference spacing between rows and plants is three centimeters by four centimeters, and approximately eight hundred and thirty cuttings can be taken per square meter. When cuttings, they should be squeezed tightly, and the depth should be about three centimeters so that they will not fall over. After insertion, water them thoroughly in time. Then build a plastic shed. It is best to put a shade net on the arch to block the sun and avoid exposure, but the weak light around 7 in the morning and after 6 in the evening should not be visible.

4. Post-insertion management:

The key to this link is temperature and humidity control. After cuttings are grafted and before roots take shape, the spray interval and spray amount should be controlled to see whether the water droplets on the leaves can be maintained; depending on the specific situation, water should be passed twice a day to ensure that the humidity is not less than 80%. Normally, some roots will appear after fourteen days, and ninety percent of the cuttings will take root after twenty days. Fertilization should be applied half a month after rooting, and the medicine prepared according to a special formula should be sprayed once every ten days. After the weather gets cold, you need to protect the plants from the cold, and then you can transplant, plant and cultivate them in early spring of the next year.

<<:  How Chiho-tani reproduces

>>:  How to grow the weeping angel well

Recommend

What to do if the leaves of the lucky tree are dry

1. Waiting for adaptation Reason: If the plant is...

When and how to plant Artemisia selengensis

Artemisia selengensis planting time Artemisia sel...

When does gardenia bloom? Gardenia pictures

1. When does it bloom? Gardenia is a very beautif...

How to care for peony flowers in four seasons

How to care for peony flowers in spring Repotting...

How to water ginkgo potted plants

Key points for watering potted ginkgo Although po...

Which month is suitable for planting double-season wild rice?

When to plant double-season wild rice stems Doubl...

How to grow zebra flowers

1. Proper lighting It likes sunlight, but is afra...

Where are Chinese cherries produced?

1. Producing Areas In my country, there are many ...

What is the best fertilizer for aloe vera?

Aloe Vera Fertilizer Time Aloe vera is generally ...

Breeding methods and precautions for mandarin fish

Mandarin fish, also known as osmanthus fish, belo...

5 tips for watering flowers in summer

Water Quality When it comes to choosing water, th...

How to grow jasmine

1. Breeding environment 1. Temperature: Jasmine s...

How to propagate magnolia and what to pay attention to

Magnolia reproduction method There are two ways t...

What does the money tree mean?

Meaning It should be clear from the name that it ...